Fiber optic connector end-face contamination is a leading cause of fiber failures. Dirt and contaminant cause insertion loss and back-reflection that inhibits optical transmission and causes havoc with transceivers. Fiber loss and OTDR testing can expose this problem, but in many cases, dirty connections make fiber testing time consuming and inaccurate.
Since dirt can be an issue before, during, or after fiber optic certification testing, and migrate from one fiber optic connector end-face to another upon mating, both sides of any connection must always be cleaned and inspected. Further, mating contaminated fiber optic connectors can cause permanent damage as microscopic debris is crushed between end-faces in physical contact. Even factory terminated patch cords or pigtails must be inspected as protective caps do not keep fiber optic connector end-faces clean. Avoiding this common cause of failure, starts with inspecting the fiber optic connector end-face and eliminating any contamination before insertion into a bulkhead or piece of equipment.
The FI-7000 FiberInspector Pro is a fiber optic inspection scope that allows you to inspect and certify fiber optic connector end-faces in 1 seconds so you can get the job done the first time. This fiber optic inspection scope provides automated PASS/FAIL certification take the guess work out of fiber inspection so anyone can be a fiber expert.
Certify your fiber end-faces to industry standards – IEC 61300-3-35. Or if you prefer, you can manually grade your end-faces.
FiberInspector Pro highlights defects found on fiber end-faces. Instead of just coloring the defect area, the FI-7000 colors the defect and highlights the defect’s background so that the defect is clearly visible. Defects that fail the standard’s requirements are colored Red, while defects that pass are colored Green.
Store both end-face images of a fiber directly in your Versiv test results. Combine end-face images with CertiFiber Pro OLTS and/or OptiFiber Pro OTDR test results for the complete history of your fiber cabling health.
The FI-7000 is built on the Versiv Cable Certification Platform which enables you to easily add optical loss (OLTS) and Optical Time Domain Reflectometry (OTDR) or even twisted pair copper or network analysis functionality to FI-7000. Product add-on kits are available for the DTX CableAnalyzer, CertiFiber Pro OLTS, and OptiFiber Pro OTDR.
Versiv’s ProjX™ System manages jobs from setup to systems acceptance, ensuring that all tests are completed correctly. Enter the testing details for a job once, and ProjX stores them in a project file with a name the whole team can understand. Change modules or jobs without having to re-enter details. Support multiple testers on the same job by sharing project files via USB sticks or email. Easy just met efficient.
|Set-up or view test limits, and testing attributes.||Project menu screen shows percent complete|
|Project Specific screen shows up to the minute project details.|
Now you can test across multiple media types and requirements as easy as using a smartphone. Simply, select the job you’re working on, and the large display confirms the test that needs to be performed. Taptive helps you tap into the overall cabling infrastructure faster and more easily.
|Taptive user interface simplifies set-up,|
eliminates errors and speeds troubleshooting.
LinkWare Live is a cloud-based service that lets you manage certification jobs anytime, anywhere, with anyone on any device. With LinkWare Live, you can
*See supported countries.
Project managers have full capabilities to monitor workflow and consolidate test results.
LinkWare pulls data togther into a single report that is easy for customers to understand, showcasing quality and workmanship. LinkWare stats, provides automated statistical reports that turns test results into charts to reveal performance. The report even summarizes your entire cabling and fiber infrastructure in one compact, graphical format, so it is easy to verify margins and anomalies.
|Integrate tests from different testers into one unified report.||LinkWare Stats summarizes all project data|
The FI-7000 models are available in 2 versions: wireless and non-wireless. The Wireless version includes integrated Wi-Fi for uploading results to LinkWare Live. The integrated Wi-FI is disabled in the non-wireless versions for customers who do not wish to receive Wi-Fi
|FI2-7000||The FI2-7000 FiberInspector Pro contains: Versiv Mainframe, USB Fiber Inspection Video Probe with 4 tips in a box (LC, FC/SC bulkhead, 1.25 and 2.5mm universal), Blank Module to protect the mainframe’s rear connector, AC Charger, Shoulder Strap, USB Interface Cable, Versiv Open Source Software CD, Integrated Wi-Fi, Getting Started Guide, Soft Carrying Case. See Photo|
|FI2-7000-NW||Same configuration as the FI2-7000 with integrated Wi-Fi disabled.|
The FI2-7000 FiberInspector Pro with MPO tip and cleaning contains: Versiv Mainframe, USB Fiber Inspection Video Probe with 4 tips in a box (LC, FC/SC bulkhead, 1.25 and 2.5mm universal), MPO Fiber Inspection Adapter Tip, Quick Clean Cleaners for 1.25mm & 2.5mm ferrules and MPO connectors, Blank Module to protect the mainframe’s rear connector, AC Charger, Shoulder Strap, USB Interface Cable, Versiv Open Source Software CD, Integrated Wi-Fi, Getting Started Guide, Soft Carrying Case. See Photo
|FI2-7000-MPO-NW||Same configuration as the FI2-7000-MPO with integrated Wi-Fi disabled.|
A USB Fiber Inspection Video probe which works with the Versiv products (CertiFiber Pro, OptiFiber Pro, and DSX CableAnalyzer). See Photo
A USB Fiber Inspection Video probe for Versiv products plus tip set (LC, FC/SC bulkhead, 1.25 and 2.5mm universal tips in a box). See Photo
|FI1000-TIP-KIT||4 FI-1000 tips in a box (LC, FC/SC bulkhead, 1.25 and 2.5mm universal)|
SC and FC bulkhead video probe tip. See Photo
LC bulkhead video probe tip. See Photo
Extended LC bulkhead video probe tip. See Photo
ST bulkhead video probe tip. See Photo
MU bulkhead video probe tip. See Photo
E2000/APC bulkhead video probe tip. See Photo
SC/APC bulkhead video probe tip. See Photo
E2000 bulkhead video probe tip. See Photo
LC/APC bulkhead video probe tip. See Photo
2.5 mm universal video probe tip for patch cords. See Photo
|FI1000-1.25-UTIP||1.25 mm universal video probe tip for patch cords|
Video probe tip for LC simplex and duplex connectors. See Photo
2.5 mm APC universal video probe tip for patch cord. See Photo
|FI1000-MPO-UTIP||MPO probe tip and translator knob for patch cords and bulkheads|
|FI1000-MPO-XY-UTIP||MPO probe tip and translator knob for multi-row patch cords and bulkheads|
MPO/APC probe tip and translator knob for patch cords and bulkheads. See Photo
MPO/APC probe tip and translator knob for multi-row patch cords and bulkheads. See Photo
1.25 mm APC universal video probe tip for patch cords. See Photo
|FI1000-MPOAPC-RT||MPO/MTP APC replacement tip with no translator knob|
|FI1000-MPO-RT||MPO/MTP replacement tip with no translator knob|
Quick Clean Cleaner 1.25 mm Fiber, LC and MU, 5 pack
Quick Clean Cleaner 1.25 mm Fiber, LC and MU, Single
Quick Clean Cleaner 2.5 mm Fiber – SC, ST, FC, E2000, 5 pack
Quick Clean Cleaner 2.5 mm Fiber – SC, ST, FC, E2000, Single
Quick Clean Cleaner MPO Fiber, Single
Quick Clean Cleaner MPO Fiber, 5 pack
Enhanced Fiber Optic Cleaning Kit – Includes an QuickClean 1.25mm cleaner, an QuickClean 2.5mm cleaner, an QuickClean MPO cleaner, a solvent pen, a cleaning cube and a softcase. See Photo
WiFi Adapter for Versiv Mainframe. (Available in the following countries.)
Versiv Large Carry Case See Photo
Versiv Small Carry Case. See Photo
Backpack strap for Versiv Large Case See Photo
|PWR-SPLY-30W||30W Power Supply, 15V, 2A with US adapter. See Photo|
30W Power Supply, 15V, 2A with US, EU, AU, and UK adapters See Photo
30W Power Supply, 15V, 2A with US, South Africa and India adapters See Photo
|PWR-SPLY-ADP||EU, AU, UK adapters for 30W power supply. See Photo|
South Africa and India adapters for 30W power supply See Photo
|Inspection Probe specifications|
|2M pixels||Blue LED|
|Light source||Blue LED|
|Power source||Versiv mainframe|
|Field of View (FOV)||Horizontal: 425 µm|
|Vertical: 320 µm|
|Minimum detectable particle size||0.5 µm|
|Dimensions||Approximately 6.75 in x 1.5 in (1175 mm x 35 mm) without adapter tip|
|Temperature range||Operating: 32°F to 122°F (0 °C to +50 °C)|
|Storage: -4°F to +158°F (-20°C to +70°C)|
|Weight||Mainframe with module and battery: 3 lbs, 5 oz (1.28 kg)|
|Dimensions||Mainframe with module and battery: 2.625 in x 5.25 in x 11.0 in ( 6.67 cm x 13.33 cm x 27.94 cm)|
|Battery||Lithium ion battery pack, 7.2 volts|
|Battery life||Eleven hour with Inspection probe attached|
|Integrated Wi-Fi||Meets IEEE 802.11 a/b/g/n; dual band (2.4 GHz and 5 GHz)|
|Tester Off||Four hours to charge from 10% to 90% capacity|
|Tester On||Six hours to charge from 10% to 90% capacity with the tester on|
|Operating temperature*||-18ºC to 45ºC|
|Non-operating temperature||-30ºC to 60ºC|
|Operating altitude||4,000 m (13123 ft)|
|3200 m (10,500 ft) with ac adapter|
|Storage altitude||12,000 m|
|* Do not keep battery at temperatures below -20°C (-4°F) or above 50°C (122°F) for periods longer than one week to maintain battery capacity.|
@ 2020 PT Media Teknologi Globalindo. All rights reserved